Fletch Type 1
*** Feathers Sold Separately ***
The Fletch is a handmade sterling silver feather holder that attaches to hat bands. There are 2 types.
This Listing is for the Fletch Type 1.
Feather Size Disclaimer: If you choose to use your own feather, be aware that the Fletch diameter is not one-size-fits-all, and your feather might not fit. The Fletch is designed to accommodate medium-to-larger feathers (such as turkey tail feathers) with a quill that is 4.5 mm - 5 mm in diameter. That typically means a feather that is 10” - 12” long.
The Fletch Type 1 is for hat bands that are 1/2” or wider. Please only purchase this type if you have a hat band that is at least 1/2” wide.
For the thinner factory-stock hat bands (the ones that come on cowboys hats directly off the rack and are tied on the side OR have a 3-piece buckle set) please purchase the Fletch Type 2.
Please carefully select your hat band width below. The tab on your Fletch Type 1 will be custom cut to accommodate your specific hat band width. Again, please pay careful attention when making your selection. Returns and alterations *wil not be accepted* due to incorrect size.
Size options are as follows:
Band Width A: 1/2” to 3/4”
Band Width B: 1” to 1 1/4”
Band Width C: 1 1/2” - 2”.
Again, please note that the Fletch Type 1 is for wider hat bands like leather bands, tall ribbons, and beaded bands. These bands are typically between 0.5 inches to 2 inches tall. Fletch Type 1 has a tab that goes behind your tall hat band and bends down over the top to create a clamp “C” around the band from the back side.
Fletch Type 1 is meant to go on and stay on. It is NOT meant to be switched among multiple hats. The Fletch type one can be removed and re-attached once or twice. However, sterling silver can only be bent back and forth a few times before it breaks. Don’t break your Fletch.
For thinner hat bands that tie on the side, please see the listing for Fletch Type 2.
*** Feathers Sold Separately ***
The Fletch is a handmade sterling silver feather holder that attaches to hat bands. There are 2 types.
This Listing is for the Fletch Type 1.
Feather Size Disclaimer: If you choose to use your own feather, be aware that the Fletch diameter is not one-size-fits-all, and your feather might not fit. The Fletch is designed to accommodate medium-to-larger feathers (such as turkey tail feathers) with a quill that is 4.5 mm - 5 mm in diameter. That typically means a feather that is 10” - 12” long.
The Fletch Type 1 is for hat bands that are 1/2” or wider. Please only purchase this type if you have a hat band that is at least 1/2” wide.
For the thinner factory-stock hat bands (the ones that come on cowboys hats directly off the rack and are tied on the side OR have a 3-piece buckle set) please purchase the Fletch Type 2.
Please carefully select your hat band width below. The tab on your Fletch Type 1 will be custom cut to accommodate your specific hat band width. Again, please pay careful attention when making your selection. Returns and alterations *wil not be accepted* due to incorrect size.
Size options are as follows:
Band Width A: 1/2” to 3/4”
Band Width B: 1” to 1 1/4”
Band Width C: 1 1/2” - 2”.
Again, please note that the Fletch Type 1 is for wider hat bands like leather bands, tall ribbons, and beaded bands. These bands are typically between 0.5 inches to 2 inches tall. Fletch Type 1 has a tab that goes behind your tall hat band and bends down over the top to create a clamp “C” around the band from the back side.
Fletch Type 1 is meant to go on and stay on. It is NOT meant to be switched among multiple hats. The Fletch type one can be removed and re-attached once or twice. However, sterling silver can only be bent back and forth a few times before it breaks. Don’t break your Fletch.
For thinner hat bands that tie on the side, please see the listing for Fletch Type 2.
*** Feathers Sold Separately ***
The Fletch is a handmade sterling silver feather holder that attaches to hat bands. There are 2 types.
This Listing is for the Fletch Type 1.
Feather Size Disclaimer: If you choose to use your own feather, be aware that the Fletch diameter is not one-size-fits-all, and your feather might not fit. The Fletch is designed to accommodate medium-to-larger feathers (such as turkey tail feathers) with a quill that is 4.5 mm - 5 mm in diameter. That typically means a feather that is 10” - 12” long.
The Fletch Type 1 is for hat bands that are 1/2” or wider. Please only purchase this type if you have a hat band that is at least 1/2” wide.
For the thinner factory-stock hat bands (the ones that come on cowboys hats directly off the rack and are tied on the side OR have a 3-piece buckle set) please purchase the Fletch Type 2.
Please carefully select your hat band width below. The tab on your Fletch Type 1 will be custom cut to accommodate your specific hat band width. Again, please pay careful attention when making your selection. Returns and alterations *wil not be accepted* due to incorrect size.
Size options are as follows:
Band Width A: 1/2” to 3/4”
Band Width B: 1” to 1 1/4”
Band Width C: 1 1/2” - 2”.
Again, please note that the Fletch Type 1 is for wider hat bands like leather bands, tall ribbons, and beaded bands. These bands are typically between 0.5 inches to 2 inches tall. Fletch Type 1 has a tab that goes behind your tall hat band and bends down over the top to create a clamp “C” around the band from the back side.
Fletch Type 1 is meant to go on and stay on. It is NOT meant to be switched among multiple hats. The Fletch type one can be removed and re-attached once or twice. However, sterling silver can only be bent back and forth a few times before it breaks. Don’t break your Fletch.
For thinner hat bands that tie on the side, please see the listing for Fletch Type 2.